Track My Order
Frequently Asked Questions
International Shipping Info
Send Email
added to your cart!
We designed this board to give the user a low profile button without any sharp edges. Button closes when you push it and open…
It's the end of the world, and you need a button to press. This is it. A 100mm diameter (outside diameter) dome illuminated p…
This is a simple 4-pack of momentary, multicolor buttons, great for all sorts of projects! Unlike previous iterations of mult…
This is a simple 12-pack of momentary, multicolor buttons, great for all sorts of projects!
This is a perfect choice if you are in need of a heavy duty push button! These metal push buttons are a very tough, small, pa…
This IR proximity contactless button makes for a good replacement for typical push buttons
The SparkFun Qwiic Button with red LED simplifies all of those nasty worries away into an easy to use I2C device, no solderin…
This is a standard 12mm square momentary button. What we really like is the large button head and good tactile feel (it 'clic…
The SparkFun Qwiic Button with green LED simplifies all of those nasty worries away into an easy to use I2C device, no solder…
Miniature surface mount momentary button. These are great, low-profile momentary switches. Perfect as a tactile reset switch.…
It's your basic black action button! This is a very useful, small, panel-mount momentary switch. It is a SPST N.O. with the t…
This is an SMD 6mm square SPST button. What we really like is the little button head and good tactile feel (it ‘clicks’ r…
This is a 35mm concave momentary push button similar to the ones you find on arcade games. Simple screw in design. Perfect fo…
This is a simple LED-illuminated tactile button with a green cap. It's just like a basic tactile button, but it lights up gre…
This a simple breakout PCB for our [4x4 silicone button pads](https://www.sparkfun.com/products/7835). Each LED and button ca…
This is a translucent silicon rubber button pad with 4 buttons orignally inspired by the folks at [monome.org](http://monome.…
This is a simple LED-illuminated tactile button with a red cap. It's just like a basic tactile button, but it lights up red! …
This is a translucent silicon rubber button pad with 16 buttons, the same found in our Simon Soldering Kits.
This is a 33mm round momentary push button similar to the ones you find on arcade games. Simple screw in design. Perfect for …
The Double Backlit user interface is like the Single Backlit Button, but twice the fun!
It's your basic red action button! This is a very useful, small, panel-mount momentary switch. It is a SPST N.O. with the thr…
The SparkFun Qwiic Button Breakout simplifies all of those nasty worries away into an easy to use I2C device, and with our Qw…
This is a black plastic bezel, custom made to mate with the silicon rubber pads. Black 1/8" ABS plastic. We use four 4/40-0.5…
This is a simple LED-illuminated tactile button with a clear cap. It's just like a basic tactile button, but it lights up whi…
This a simple breakout PCB for our [2x2 silicone button pads](https://www.sparkfun.com/products/7836). Each LED and button is…
This is a simple LED-illuminated tactile button with a clear cap. It's just like a basic tactile button, but it lights up blu…
This simple breakout board makes it easy to use our LED tactile switches in a breadboard, or your next project. **Note:** Po…
This is an SMD 12mm square SPST button. What we really like is the large button head and good tactile feel (it ‘clicks’ r…
This is a simple 4-pack of momentary, multicolor buttons, great for all sorts of projects!
This is a black plastic bezel, custom made to mate with the silicon rubber pads. Black 1/8" ABS plastic. Using two of these b…
This right-angle tactile switch has a great 'click' to it. Also, because it's a through-hole design it's very sturdy. Mount i…
Button Y Click is a Click board™ equipped with the tactile switch, sometimes referred to as a pushbutton.
