SPDT Slide Switch

This is a simple SPDT slide switch - great for use as an ON/OFF button, or just as a general control switch. The pins are spaced by 0.1", however they are incredibly thin making breadboard use not recommended. The switch is rated for 0.3A at 50VDC.

This switch is just a bit smaller than our popular SPDT Mini Power Switch, but uses the same pin spacing. Being smaller takes up less PCB space (good!), but it does make it a bit harder to hit and flip easily.

SPDT Slide Switch Product Help and Resources

Core Skill: Soldering

This skill defines how difficult the soldering is on a particular product. It might be a couple simple solder joints, or require special reflow tools.

1 Soldering

Skill Level: Noob - Some basic soldering is required, but it is limited to a just a few pins, basic through-hole soldering, and couple (if any) polarized components. A basic soldering iron is all you should need.
See all skill levels


Core Skill: Electrical Prototyping

If it requires power, you need to know how much, what all the pins do, and how to hook it up. You may need to reference datasheets, schematics, and know the ins and outs of electronics.

1 Electrical Prototyping

Skill Level: Noob - You don't need to reference a datasheet, but you will need to know basic power requirements.
See all skill levels


Comments

Looking for answers to technical questions?

We welcome your comments and suggestions below. However, if you are looking for solutions to technical questions please see our Technical Assistance page.

  • Member #1151441 / about 6 years ago / 1

    A word of warning: when soldering, use as little solder as possible. It's all too easy to form a bridge with the metal tabs on the chassis of this switch, and short the opposite throws! I definitely recommend the COM-00102 instead -- since that switch has a plastic housing this isn't a problem.

  • Member #293179 / about 8 years ago / 2

    Does anyone have a datasheet (manufacturer's) for this product?

  • Calif / about 9 years ago / 2

    Utterly worthless. Intermittent contact. No resistance to any environment but the driest indoor environment.

  • djmason9 / about 10 years ago * / 2

    If anyone is interested I made a sketchup 3D model of this

    http://sketchup.google.com/3dwarehouse/details?mid=228b41e91b3eac5e6eed87081bea555c

  • jcholton / about 9 years ago / 1

    These switches are great. I used one for my MicroMouse robot and it worked perfectly. Tip: To put these in a breadboard, first put a little bit of hot glue on the bottom. Then they won't fall out, and the glue can still be peeled off easily

  • Member #460748 / about 10 years ago / 1

    In my opinion, these are not breadboard friendly. Every time I try to switch it, it pops out of the breadboard. Having two rows of pins would make this friendlier, like the ones I got with a seeedstudio starter kit. Sadly these are not as good, and sparkfun doesn't seem to carry two-pin-row versions.

  • charredgrass / about 10 years ago / 1

    How well would this fit in a breadboard?

  • What is the digikey equivalent product?

  • So is the rating "0.3A at 50VDC correct????????

  • Could this be used with 9v at ~600 mA? I'm building a personal fan prototype with my mini breadboard (stuck to a foam block from the maglev train kit me and my friend used for NY SciOly xD) and I need either this or the other one here...
    Update: I'm getting the 4 of other one here. Or maybe this one. Thanks for the quick answer!

  • sanddrag / about 12 years ago / 1

    Perhaps the terminals on the SPDT Mini Power Switch are longer, but on this one they are just barely long enough for breadboard use. The switch barely stays in the breadboard and pops out really easily. I wish the pins were longer so it stays in better.

  • baum / about 12 years ago / 1

    Datasheet sats .2A @ 30VDC...

  • Just a guess but the dimensional drawing looks more like the COM-00102 item... the specs should be similar

Customer Reviews

No reviews yet.