Track My Order
Frequently Asked Questions
International Shipping Info
Send Email
added to your cart!
The low current version of the SparkFun Current Sensor Breakout is a high accuracy board that utilizes the ACS723 for low to …
Our through-hole Simon Says Kit is a great beginner's kit and also a pretty fun toy. All components are through-hole, making …
The SparkFun LED Project Kit is a great way to get started with programming and hardware interaction with the Arduino program…
This is a breakout board for the [L298N](http://www.sparkfun.com/commerce/product_info.php?products_id=9479) full-bridge dual…
The SparkFun MIDI Shield board gives your Arduino-based device access to the antiquated, but still widely used and well suppo…
The Qduino Mini is a tiny, Arduino-compatible board with a battery connector and charger built-in as well as a fuel gauge tha…
This is the Sunny Buddy, a maximum power point tracking (MPPT) solar charger for single-cell LiPo batteries. This MPPT solar …
This is not your normal PIR! The SparkFun AK9753 Human Presence Sensor Breakout is a Qwiic enabled, 4-channel Nondispersive I…
The new version of the UBW32 now uses the PIC32MX795 IC. Based on the work of Brian Schmalz, the UBW32 is a small development…
Is your project linked to environmental protection, awareness or study, or to protecting human life? Perhaps you are developi…
The SparkFun BMI270 Micro 6DoF IMU Breakout is a Qwiic-enabled breakout board based on the ultra-low power BMI270 from Bosch.
The SparkFun LoRaSerial Kit is a pair of serial radio modems that simply passes serial back and forth between one another.
The purple SparkFun Qwiic Alphanumeric Display allows you to display all sorts of numbers, characters, and symbols. With Qwii…
XBee radios are an awesome way to add wireless capability to your Arduino project and now it's even easier with the SparkFun …
The SparkFun OpenLog Artemis is an open source data logger that comes pre-programmed to automatically log sensor, GPS, serial…
The SparkFun BMI270 6DoF IMU Breakout is a Qwiic-enabled breakout board based on the ultra-low power BMI270 from Bosch.
The SparkFun LP55231 LED Driver Breakout is a self-contained solution for developing and deploying the nine-channel I2C LED c…
If you’re ready to step your Arduino game up from older 8-bit/16MHz microcontrollers, the SparkFun SAMD21 Dev Breakout is a…
Need a power sensor that can sense voltage up to 60VDC and current up to 30A? This is the product for you! The Allegro Mic…
The SparkFun WiFi IR Blaster is designed to connect all of those old, legacy IR-controlled devices to a WiFi network exposing…
The AS6212 digital temperature sensor from AMS provides high-accuracy temperature data combined with excellent power consumpt…
Our RedBoards are great. But don't they sometimes seem a little **_BIG_**?! Enter **smôl**, a new range of boards which a…
The SparkFun Inventor's Kit (SIK) is a great way to get started with programming and hardware interaction with the Arduino pr…
This is a basic breakout board for the FTDI FT232RL USB to serial IC. The pinout of this board matches the FTDI cable to work…
Do you have too many sensors with the same I2C address? Connect them to the SparkX PCA9846 Qwiic Mux to get them all talking …
This simple breakout board makes it easy to use our LED tactile switches in a breadboard, or your next project. **Note:** Po…
The SparkFun Qwiic Button Breakout simplifies all of those nasty worries away into an easy to use I2C device, and with our Qw…
The STMicroelectronics ST25DV _**dynamic**_ Near Frequency Communication / Radio Frequency Identification tag ICs are awesome…
Many of our Qwiic products draw very little current when in standby, but there are some that draw considerably more. Products…
A kit with basic components for using the Raspberry Pi 5 including a power supply, microSD card, and HDMI display cable.
This is a breakout for the SOIC version of the 74HC595 shift register IC. Clock in data and latch it to free up IO pins on yo…
This is the MS5803-14BA Pressure Sensor Breakout, a high resolution pressure sensor with both an I2C and SPI interface.
This is a simple breakout board for our RFID readers. The SparkFun RFID Reader Breakout converts the 2mm pins to bread board …
This sleek, red 16GB thumb drive has been emblazoned with our SparkFun Electronics logo and our moniker to Start Something!
This a simple breakout PCB for our [2x2 silicone button pads](https://www.sparkfun.com/products/7836). Each LED and button is…
The SparkFun USB-C Breakout supplies up to 3 times the power as previous USB board while breaking out each pin on the connect…
This simple board breaks out a micro-B USB connector's VCC, GND, ID, D- and D+ pins to a 0.1" pitch header. If you want to ad…
The SparkFun Qwiic Twist is a digital RGB rotary encoder breakout that is also able to connect to our Qwiic Connect System.
This is the 100mm 16-way 0.5mm-pitch Flexible Printed Circuit used to interconnect smôl boards end to end. *** _**smô…
This is the 36mm 16-way 0.5mm-pitch Flexible Printed Circuit used to interconnect smôl boards side by side. This FPC has an …
This is a low-cost, basic SOIC breakout boards. This custom PCB will interface a standard SOIC package IC to 0.1" headers, wh…
With a 32-bit ARM Cortex-M4F MCU, the SparkFun MicroMod SAMD51 Processor Board is one powerful microcontroller packaged on a …
The SparkFun OpenLog with Headers can store, or "log", huge amounts of serial data and act as a black box of sorts.
This is a breakout board for the WS2812B RGB LED. The WS2812B (or "NeoPixel") is actually an RGB LED with a WS2811 built righ…
This kit provides you with a RedBoard Turbo, two sensors, a joystick, and an OLED screen as well as all the cables you need t…
The Teensy is an amazing development platform that allows you to get more computing power than an Arduino Uno, and in less sp…
Binary Blaster is a game designed to help teach what binary numbers are and how to convert from decimal (and hexadecimal) to …
