Track My Order
Frequently Asked Questions
International Shipping Info
Send Email
added to your cart!
The SparkFun ESP32-C6 Pocket Dev Board is built around a RISC-V single-core processor with 4 MB flash memory in a 1"x1" Qwiic…
The USB-C variant of ESP32 Thing Plus is a development board with WiFi, SPP, BLE, Qwiic connector, 21 I/O pins, RGB status LE…
The SparkFun Thing Plus Matter is the first easily accessible board that combines Matter and SparkFun’s Qwiic ecosystem for…
This polarized I2C cable insulation is made from silicon making it more flexible than our original Qwiic cable particularly i…
The IoT RedBoard is an ESP32 WROOM-equipped development board that has everything you need in an Arduino Uno with extra perks…
Here is a tiny 4-pin Qwiic 1mm JST connector. This connector is used on all of our Qwiic-based boards and can be used to crea…
This is the Sunny Buddy, a maximum power point tracking (MPPT) solar charger for single-cell LiPo batteries. This MPPT solar …
This is a 100mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components together…
This is a 500mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components together…
These 2-pin JST-SM pigtail connectors mate perfectly with LED strips and other applications that require only two lines and a…
The SparkFun Logomatic v2 takes everything we learned with logging analog or serial data from your projects over the years.
The SparkFun Nano Power Timer will run while only consuming minimal power (approximately 35nA) and turn your project on after…
This is a jumper adapter cable that comes pre-terminated with a female Qwiic JST connector on one end and a breadboard hookup…
This is a unique two-cell AAA battery holder built specifically for the BBC micro:bit. The 6" (~150mm) cable has been termina…
This is a 50mm long 4-conductor cable with 1mm JST termination. It’s designed to connect Qwiic enabled components together …
This is a simple to use motion sensor. Power it up and wait 1-2 seconds for the sensor to get a snapshot of the still room. I…
MOSFETs are awesome. They're like a switch that you flip electronically! This SparkFun MOSFET Power Controller makes it easy …
If you need to charge LiPo batteries, this simple charger will do just that, and do it fast! The SparkFun USB LiPo Charger is…
These 3-pin JST-SM pigtail connectors mate perfectly with LED strips and other applications that require only two lines and a…
This is a simple six wire cable. Great for jumping from board to board or just about anything else. These cables mate with th…
The SparkFun DA16200 Thing Plus utilizes a highly integrated ultra-low power WiFi system on chip that allows users to develop…
The SparkFun AzureWave Thing Plus is a Feather form-factor development board equipped with the AW-CU488.
The SparkFun Qwiic Wireless Speaker Kit provides you with everything you need to make a wireless audio speaker.
This is a unique two-cell AA battery holde. The 6" (~150mm) cable has been terminated with a JST-PH connector.
This is a simple three wire cable. Great for jumping from board to board or just about anything else. There is a 3-pin JST co…
This 2.5W, 4 Ohm speaker is only 28mm in diameter and just over 4mm thick.
This is a classic 9V snap connector terminated with 2-pin polarized Molex connector with 0.1" spacing.
This is a simple four wire cable. Great for jumping from board to board or just about anything else. There is a 4-pin JST con…
These 4-pin JST-SM pigtail connectors mate perfectly with LED strips and other applications that require only two lines and a…
Odometers are extremely useful for cars, they tell you how far you have gone, wouldn't it be nice if you were able to have a …
The SparkFun IoT RedBoard Kit is intended to provide you with everything you need to get up and running with the IoT RedBoard…
This is a two pin, compact surface mount JST connector
This connector is used on all of our Qwiic-based boards and can be used to create your own I2C-based device compatible with t…
The LilyPad Simple Power is a simple e-textile board with a 500mA charge rate that lets you connect and charge a lipo battery…
This is a simple two wire cable. Great for jumping from board to board. 2-pin JST connector on one end, bare cable on the opp…
Behold, the Hydra! This USB power cable probably looks a lot like something you've hacked together before. We do it all the t…
Our RedBoards are great. But don't they sometimes seem a little **_BIG_**?! Enter **smôl**, a new range of boards which a…
This 3xAA battery holder with JST connector puts a nice finishing touch on your battery powered project.
Here is a six pin vertical 1.0mm pitch connector. It is useful if you need something very tiny as a connection. These are not…
Behold, the Hydra! This USB power cable probably looks a lot like something you've hacked together before.
The SparkFun Blues Wireless MicroMod Starter Kit provides every part needed to get you connected and start prototyping with t…
There is a 3-pin Molex connector on one end, 3-pin JST connector on the other both with 0.1" spacing.
