Track My Order
Frequently Asked Questions
International Shipping Info
Send Email
Jump to Subcategory:
added to your cart!
Metal Hex Male/Female standoffs. #4-40 thread with 3/8" shank and 3/16" thread length. Can be stacked to create any length. …
There are your standard Philips-head 4-40 screws. They are 1/4" long and come in packs of ten. This is the screw size we use …
These nylon standoffs are 3/4" long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or …
We could talk about how the Zinc used in these nuts is only from the finest old-growth Zinc trees from across the globe and i…
These nylon standoffs are 3/8" long and tapped for a 4-40 screw. These are great for mounting your board in an enclosure, or …
Rubber feet raise your PCB or project up off your desk. This helps prevent short circuiting from bits of scrap wire floating …
Standard Philips-head 4-40 screws. They are 1/2" long and come in packs of ten. This is the screw size we use in most of the …
These are very handy. They are simple angle brackets with one threaded and unthreaded hole. Use them for connecting PCBs at 9…
These flanged ball bearings fit nicely into a 1/2" diameter hole and has a 1/4" bore. This makes it perfect for all [Actoboti…
"Rubber" feet raise your PCB or project up off your desk.
Metal short standoffs: 3/8" long x 1/4"OD. Used to get your proto board up off the table. #4-40 thread. Fits all development …
A 5-pack of the M.2 screws that SparkFun uses with the MicroMod ecosystem.
We understand that small part tend to get lost or damaged easily. These Panel Mount Nuts are handy replacement units that fit…
These stainless steel shaft couplers allow you to couple two size shafts together. They can be used for connecting motor shaf…
This hardware kit consists of four each of M2 style nylon hex nuts and screws.
These are Philips-head M3 screws. They are 12mm long and come in packs of three. This is the screw size that the MiP robotic …
These 10" long stainless steel tubes have an outer diameter of 1", an inner diameter of 0.88", and a wall thickness of 0.06".…
Standard Philips-head 4-40 screws. They are 3/4" long and come in packs of ten. This is the screw size we use in most of the …
These center hole adaptors come in packs of four, are .08” thick, and have an outer diameter .54”. Their ½” diameter l…
These 2" long aluminum tubes have an outer diameter of 1", an inner diameter of 0.82", and a wall thickness of 0.09". When us…
These plastic shaft spacers have an inner diameter of 5/8” and a thickness of 1/16”. These spacers are ideal for spacing …
These are standard screws with 2-56 thread and 3/8" long, recommended for the small button pad sets. Can be used with a 2-56 …
These 10" long aluminum tubes have an outer diameter of 3/8", an inner diameter of 0.30", and a wall thickness of 0.035". Whe…
**Description**: These are standard nuts with 2-56 thread. For use with 2-56 machine screws and five button pad set listed be…
TE Connectivity's Anti-Vandal Pushbutton Switch Hardware consists of nickel-plated brass hex nuts and silicone O-rings.
These 10" long aluminum tubes have an outer diameter of 5/8", an inner diameter of 0.569", and a wall thickness of 0.028". Wh…
These dolly wheel drive plates provide you with a way to create an easy to assemble, low friction, drive system or motorized …
A portable hardware kit for experimenting with pneumatics
**Replacement:**[PRT-10927](http://www.sparkfun.com/products/10927). These are now sold in packs of ten! This page is for ref…
These 8" long stainless steel tubes have an outer diameter of 1", an inner diameter of 0.88", and a wall thickness of 0.06". …
These dolly wheel drive plates provide you with a way to create an easy to assemble, low friction, drive system. The idler A …
These plastic shaft spacers have an inner diameter of 1/2” and a thickness of 1/16”. These spacers are ideal for spacing …
